How to keep the displays clean

The rag must be clean(store displays)
When cleaning and maintaining the display rack, be sure to determine whether the rag used is clean. After cleaning or wiping off the dust, be sure to turn over or change a clean rag before use. Don't be lazy and reuse the dirty side again and again, which will only make the dirt rub on the surface of commercial furniture repeatedly, but will damage the bright surface of the display shelf.

Nursing agent selection(store displays)
To maintain the original brightness of the display rack, there are two kinds of display rack maintenance products: display rack care wax spray and cleaning and maintenance agent. The former mainly aims at the display shelves made of various wood, polyester, paint, fireproof rubber board and other materials, and has two different fresh flavors of jasmine and lemon. The latter is suitable for all kinds of solid wood display racks such as wood, glass, synthetic wood or Meinai board, especially for mixed material display racks. Therefore, if you can use maintenance products with both cleaning and nursing effects, you can save a lot of valuable time.

Before the use of wax spray and cleaning agent, it is best to shake it up first, then hold the spray tank straight, at a 45 degree angle, so that the liquid components in the tank can be released completely without losing pressure. After that, spray the dry rag gently at a distance of about 15 cm, so as to wipe the commercial furniture, which can have a good cleaning and maintenance effect. In addition, remember to wash and dry the rag after use. As for the display rack with cloth material, such as cloth sofa and leisure cushion, you can use the cleaning and maintenance agent to clean the carpet. When in use, use a vacuum cleaner to remove the dust, and then spray a small amount of carpet cleaner on a wet cloth to wipe it.

Paint watermark removal(store displays)
A circle of annoying watermarks are often left on the painted table after leaving the wet tea cup. How can we quickly remove them? You can spread a clean wet cloth on the watermark on the desktop, and then iron it with an iron at a lower temperature. In this way, the moisture penetrating into the paint film can evaporate, so that the watermark disappears. However, when using this method, the rag used should not be too thin, and the temperature of the iron should not be adjusted too high. Otherwise, the watermark on the desktop will disappear, but the brand will never be removed.

Maintenance of iron exhibition stand(store displays)
The iron exhibition stand has the characteristics of durability and durability. Generally speaking, daily wear and tear can make it more antique, but this does not mean that the iron exhibition stand does not need maintenance. Due to the particularity of its material and technology, the maintenance of iron exhibition rack also has special places:

1、 Outdoor iron exhibition stand
The selection of materials for outdoor iron exhibition racks requires rust prevention, wear resistance, corrosion resistance, exposure resistance, etc. Generally speaking, in the production process, the manufacturers have taken into account the characteristics of the outdoor environment, so users only need to identify the well-known manufacturers when purchasing, and don't be greedy for cheap to buy some unqualified ones. But the following must be done:

1. Dust removal.
There is a lot of dust outdoors. Over time, there will be a layer of dust on the surface of the exhibition stand. It will affect the effect of the exhibition stand, and a long time will lead to the damage of the protective film on the exhibition stand. Therefore, the outdoor iron exhibition stand should be wiped regularly, generally with soft cotton fabric.

2. Moisture proof.
In the north, you can rest assured of the rust resistance of the iron exhibition stand. In foggy weather, wipe off the water drops on the exhibition rack with dry cotton cloth; On rainy days, wipe the water droplets in time after the rain stops. When selecting exhibition racks in the south, we must pay attention to the selected steel models. (this was introduced in the previous article.)

Indoor iron exhibition stand
1. Avoid collision.
This is the first thing to pay attention to after purchasing the iron exhibition rack. The exhibition rack should be handled with care during handling; The place where the exhibition stand is placed should be a place where hard objects do not often touch; Once a place is selected, it should not change frequently; The ground on which the exhibition stand is placed shall also be kept flat to make the four legs of the exhibition stand stable. If it is unstable, the exhibition stand will be slightly deformed over time and affect the service life of the exhibition stand.

2. Clean dust removal.
It is best to use pure cotton knitwear as rag to wipe the surface of the exhibition stand. Pay attention to the dust in the depressions on the display frame and the relief decoration.

3. Keep away from acid and alkali.
Acid and alkali that corrodes iron is the "number one killer" of iron exhibition stands. If acid (such as sulfuric acid and vinegar) and alkali (such as methylalkali, soapy water and soda water) are inadvertently stained on the iron exhibition stand, clean the dirty place with clean water immediately and wipe it dry with dry cotton cloth.

4. Keep away from the sun.
The display stand should be placed away from the direct sunlight outside the window. If the iron exhibition stand is exposed to the sun for a long time, the paint color will change; The colored paint layer is dry cracked and peeled, and the metal is oxidized and deteriorated. In case of strong sunlight and unable to remove the exhibition rack, it can be covered with curtains or shutters.

5. Keep away from moisture.
The indoor humidity shall be maintained within the normal value. The exhibition stand shall be far away from the humidifier. Moisture will cause metal corrosion, chromium plating and film removal. During the large-scale cleaning of the exhibition stand, do not clean the exhibition stand with boiling water. You can wipe it with a wet cloth, but do not wash it with running water.

6. Remove rust.
If the exhibition stand is rusty, don't sand it with sandpaper. If the rust is small and shallow, cotton yarn can be dipped in engine oil and applied to the rust. After a while, wipe it with a cloth to eliminate the rust. If the rust has expanded and become heavier, please ask relevant technicians to repair it.